搜索资源列表
prototype
- Qt界面，实现好底层驱动继而控制马达转速，角度。-Qt interface to achieve good underlying driver then controls the motor speed, angle.
PCB12
- 对于驱动电路模块 驱动电机的PCB布线设计以及原理图-For the driver circuit module PCB wiring design and schematic diagram of the driven motor
Compass-MSP430
- 基于MSP430的电子罗盘，控制步进电机带动指针指向正北，并将电子罗盘数据及单片机平台的航向通过蓝牙串口发送至PC端程序上显示。实现了MSP430包括HM3883l电子罗盘、步进电机、带软件FIFO的串口模块的驱动。-Electronic compass based on MSP430, control the stepping motor drives the pointer points to the north, and the electronic compass data and si
GccApplication2
- L293 D DRIVER MOTOR DC MOTOR
code
- 两轮自平衡车 430做处理器，MPU6050,1:90大扭矩电机， L298驱动，2576稳压，用的平衡互补滤波和PID-Two self-balancing vehicle msp430 processor, MPU6050,1: 90 high-torque motor, L298 driver, 2576 regulator, with the balance of complementary filtering and PID
code_driver_may-ban-tam
- driver DC motor by PWM with PIC16f887
bujindianjiceshi
- STM32奋斗板步进电机测试,演示的是通过C口的4个口线利用tim2定时器，固定周期产生4路的脉冲信号模拟步进电机的4相8拍控制组合。步进电机采用型号为5V 28BYJ-48的步进减速电机。步进角 5.625度/64驱动板采用ULN2003驱动板。-STM32 struggle board stepper motor testing, demonstration by four port line C port utilization tim2 timer, fixed cycle 4 puls
stepmotor-zhengfanzhuan
- 步进电机正反转驱动程序，可以通过按键将步进电机的正反调整，很有用的-Stepper motor reversing driver, you can adjust the key to reverse the stepper motor, very useful
BLDC-firmware
- 三相六拍直流无刷电机驱动固件，采用的TI的方案，已经用在我们公司的无刷圆锯上面了。特共享出来换积分-This is the driver for BLDC motor ,this firmware has been used on our BLDC product.
L298N-Arduino-
- Arduino 的学习笔记，通过驱动板L298N来驱动两个直流电机，电子书PDF，书上附代码-Arduino study notes, two dc motor can be driven by L298N driver board, e-book PDF, the book attached code
MusicRobot
- RobotMusic可以敲音乐的机器人，用Arduino控制，步进电机作为驱动！-RobotMusic can knock on music robot, use the Arduino to control, step motor as the driver!
L298N
- 基于L298的电机驱动开发的原理图及相关驱动程序例程，很好的参考资料哦！-L298 motor-driven development based on schematics and associated driver routine, a good reference Oh!
PWM
- PLC s7200 PWM for control driver servo motor
PMSMtables
- PMSM table for driver for PMSM motor
Ultrasonic-wave-smart-car
- 基于51单片机的超声波侧墙小车 电机驱动L298N 设置距离15cm 检测到前方障碍后后退重新检测 未设置侧墙后的行走算法。预留12864显示接口-L298N driver set the distance 15cm not set after walking algorithm sidewall 51 single ultrasonic motor car sidewall. Reserved 12864 Display Interface
LCD-Drivers
- 为C语言触控屏幕驱动程序。通过显示屏的操作，控制电机，步进电机与LED。触控屏型号为MZTH35 V10彩色液晶。 程序在LCD上编辑了一个“九宫格”小游戏。对LCD驱动的编程具有一定指导意义。-LCD touch screen driver. By operating the LCD, to control the motor, stepper motor and LEDs.The LCD touch screen model is MZTH35 V10.
ultrasonic
- 基于51单片机的智能车避障源程序。在本装置中，用遥控器控制小车前进、后退、左转、右转运动来模拟驾驶员的驾驶动作；小车的最前部安装有超声波传感器，用于检测本车与前面障碍物的距离；电路板安装于小车的车架上；原车的后桥驱动电机和转向电机的布置基本不变。本装置的基本原理为：超声波发射端在单片机和前置电路的驱动下工作，接收端的信号经放大整形后在单片机的中断口产生中断，通过发射和接收的时间差计算出小车与障碍物的相对距离，再由单片机实现避障算法，做出判断决策，发出相应的控制指令，然后通过外围硬件电路实现PWM
StepControlSource
- 串口总线控制型步进驱动器调试软件，具有参数设置、保存、导入功能，可Jog控制步进电机运动。在此基础上可方便地开发其他型号的串口驱动器控制程序-Serial bus controlling stepper driver debugging software, with parameter setting, save and import function, can be worldwide control stepping motor sports
Module1-1(DriverPMotor)
- start dc motor with driver l298
Module2-1(DriverPMotorPAVR)
- start dc motor using driver